wireless1

Sa.gif (46837 bytes) Brochure1      Brochure
                                           Brochure2
        2.4G Wireless Security System +Receiver                        Order No.1680004
Features

Ultra High Frequency (2.4Hz)transmission, less prone to interface
Highly sensitive 1/3"black /white CCD Camera, 420 line high resolution
4-Channel transmission module is built-in . Option to send signal by any of the 4 channel
4-Channel receiving module may receive signals simultaneously from up to 4 camera
Facilitate scalable approach so users can install 1 camera to start with and upgrade to 4 cameras later on
Receiving module automatically receives new signal as new cameras are added to service
Receiving module can be adjusted to mute or changing interval of scanning
Audio effect clear and Video effect stable
Transmission distance can be up to 150 Meters
Can be connected to VCR for recording purpose
Easy to install and easy to operate
Wireless transmission so it reduces the cost of wire installation

Receiver User Manual:

1.This unit is controlled by advanced micro processer.

2.In one-to-one transmission/receiving mode, please follow the steps described in other pages.

3.If more than one camera is installed:

Install each camera respectively according to camera installation procedure
Set the camera to channel 2,3,4 respectively according to the set up.
Power on receiver and the LED indicator will lit.Press the SET key and then press the CH1,CH2,CH3,or CH4 key according to your setup on cameras.
When all set, press the SET key again so the set up process is complete.
The LED will extinguish and the channel LED indicator will start blinking order by your setup.
If desire to receive a particular transmission channel from a camera, simply press the CH1,CH2, CH3,or CH4 key.
If desire to adjust timer for scanning, please use a regular screw driver to adjust the key clockwise .This will slow down the timing for scanning.
Press MUTE key for quiet transmission.

Lcd1.gif (3335 bytes) Video Camera W/Antenna Install procedure

Fasten Camera onto the mounting rack, Looking for appropriate place for installation
Insert into antenna or power and it should be done
Transmission channel can be chose selectively
If transmission channel is set to CH1,the receiving channel should be set to CH1 also

Lcd2.gif (5185 bytes) Receiver/TV Installation Procedure:

Connect AV output on the receiver with the AV input on the TV using cable
Turn on TV and set it to AV mode
Power on receiver using AV mode
Note:Antenna should be in place

Self Diagnosis and Resolution

Symptom	Possible Cause	Resolution
Power Off	Power is not hocked	Insert power cord to a socket
Power on,but not operable	Static effect	Unplug power cord and re-plug back in after a few minutes
No Picture, No Sound	Power is not connected properly	Insert power cord to a socket
	Power is not turn on	Turn on the Power key
	Antenna on the receiver is not connected or worn out	Check if the antenna is worn or is not connected properly
	Audo/Video wire touch each other	Check if the wire is corn or is not connected properly
Sound great , picture poor	Antenna is not connected properly or wire is worn out	Chick if the wire is worn or is not connected properly
Sound great , picture poor	Possibly effected by terrain	Remove antenna from the effected area
Sound poor, picture great	Possibly effected by terrain	Remove antenna form the effected area
Sound poor, picture great	Volume was set too high	Lower the volume
Cannot record image/sound	The writeable knob is broken on tape cartridge	Change a new tape
	Audio/Video wire touch each other	Change if the wire is worn or is not connected properly
	Pre-set recording function has started	Turn off pre-set function

ADD : 6F,NO. 15, LANE 131, HANGCHOW SOUTH ROAD IST SECTION

TAIPEI TAIWAN R.O.C.
TEL : 886-2-23214118 FAX : 886-2-223910073
Sales e-mail : yokojima
Customer support e-mail : Albert
Technical support e-mail : Vincent
INTERNET PHONE ( NETMEETING ) :
Fax-ON-DEMAND : 886-2-23210073